![fox float rp23 travel specs fox float rp23 travel specs](https://images.immediate.co.uk/production/volatile/sites/21/2019/03/1314191287806-177sgqhs157j6-5926558.jpg)
With the presentation of the first mountain bike fullys at the end of the 1980s, the development of specific MTB suspension forks and shocks began. In 1983 FOX shock absorbers already started dominating the US-American car and motorcycle racing sport. In addition to motocross, FOX Racing Shox also made a name for itself in the late seventies in off-road car racing. Only a few months later it went into production and enabled victories in countless road and cross-country races. Should only be adjusted while in a stationary position.In 1974 the company founder Bob Fox developed the first prototype of the FOX AirShox air damper for a motocross bike. Occurs as you exit the current setting the second click as you engageĬAUTION:The ProPedal knob should NOT be adjusted on-the-fly. The ProPedal knob clicks twice per setting as it turns. You want-1, 2, or 3-is aligned with the ProPedal lever ( #3). The three ProPedal knob settingsĬlockwise (relative to the ProPedal knob facing the user) until the selection The numbers etched onto the ProPedal knob. The ProPedal knob settings are denoted by Knob only changes damping when the ProPedal lever is in the PROPEDAL The 3-position ProPedal knob (shown below)Īllows you to adjust ProPedal firmness when the ProPedal lever is in the Suspension movement most effectively while providing the desired amount The ProPedal lever, switch positions and select a setting that reduces Vary, optimal settings can vary from bike to bike and rider to rider.įor more precise ProPedal tuning and to further eliminate pedal-inducedīob while maintaining bump compliance, adjust the ProPedal knob. Movement most effectively while providing the desired amount of bump absorption.īecause suspension designs and riding skills Switch between positions and select the one that reduces suspension To determine which ProPedal position is betterįor your condition and situation, pedal the bicycle and monitor the shock For example, use PROPEDALįor riding to the top of the mountain, and then switch to OPEN for the descent. The two ProPedal lever settings are:ĭifferent riding conditions and situations. ProPedal damping reduces pedal-induced suspensionīob. Rebound, turn the red adjuster knob counterclockwise.
![fox float rp23 travel specs fox float rp23 travel specs](https://www.ridefox.com/fox_tech_center/owners_manuals/010/fre/Content/float_rp23_french__450x252.gif)
Rebound, turn the red adjuster knob clockwise. The rebound knob has 8-10 clicks of adjustment. Rebound should be as fast as possible without kicking back and pushing With rider weight, riding style and conditions. The proper rebound setting is a personal preference, and changes Rebound controls the rate at which your shock returns after it has beenĬompressed. Proper sag is achieved, then replace the air valve cap. Spring Setting Guidelines table below for the proper sag setting. Do not over-tighten.ĭesired pressure is shown on the gauge. Racing Shox High Pressure Pump onto the air valve until the pump shows Continue if the sag is not to specification.Īir valve on the shock and remove the air valve cap. Sag, and compare it to the recommended sag setting shown in the Air Spring Setting Guidelines tableīelow. Check that the front and rear brakes operate properly.Check that brake cables or hoses are properly.Pinch bolts) are properly adjusted and tightened. Check that quick-release levers (or thru-axle.Or FOX Racing Shox for further inspection and repair. Shock should not be used if any of the exterior parts appear to be damaged. Inspect entire exterior of shock for damage.Do not use a high pressure washer on your shock. Note:Do not use any solvents or de-greasers, as these products can damage the shock's exterior finish or its anodized parts.ĭo not spray water directly on the seal/shock body junction. Clean the outside of your shock with only mild soap and water,.Checkīe performed by FOX Racing Shox or an Authorized Other things to consider for all shock models:Ĭonditions, service your shock and air sleeve more frequently. This is an indication that the air sleeve should be re-lubricated.
![fox float rp23 travel specs fox float rp23 travel specs](https://p.vitalmtb.com/photos/products/4693/photos/3924/s1600_fk260a12.jpg)
If this residual air sleeve lubricant is not present, There may be a small amount of air sleeve lubricant residue on the body. Tune to a more specific air pressure in the Setting Of the shock are clear of the frame and swingarm as it cycles throughĪir chamber to a minimum of 50 psi and no more than 300 psi. If you are installing your shock on a bike in which the shock is notĬhamber air cap and let all the air out of the main air chamber. High volume standard air sleeve, boost valve, angled air valve, lightweight chassis, DOHC ProPedal with 2 positions, ProPedal tuning adjust with 3 positions, air spring pressure, Safety Information | Stuck Down Shock | Air Sleeve Maintenance Sag | Setting Sag | Adjusting Rebound | ProPedal | Service Intervals | Important Installing Your Shock | General Maintenance | Before You Ride | Measuring You are here: Rear Shocks > FLOAT > FLOAT RP23